Home / Resources / How to clean a hot melt system

How to Clean a Hot Melt System

Purge and clean while the unit is at operating temperature. Qualified personnel only. Wear heat-resistant gear. Call 800-249-0337.

Plant-floor overview, about 1 minute.

How do I clean a hot melt tank?

With the unit at operating temperature, drain the old adhesive, remove loose char with a non-metal tool, load a purge matched to your adhesive, and run it through the tank, hoses and nozzles until it comes out clean. Change filters, clean or replace nozzles, then flush with fresh adhesive before you start production.

Call 800-249-0337

For common industrial hot melt melters. Always follow your equipment maker’s safety manual and the SDS for every product you use. Hot melt causes burns. Call us for data sheets.

Cleaning steps

  1. Keep the unit at operating temperature. Drop pump pressure to zero.
  2. Drain the tank through the drain or bypass, following your equipment maker’s steps.
  3. Remove loose char, skins and gel with a wood, plastic or PTFE spatula. Do not use metal tools on a coated tank.
  4. Load a purge matched to your adhesive (see the table below) and let it melt fully.
  5. Disconnect the nozzles. Run purge through the hoses and guns into a container until it comes out clean.
  6. Change tank and inline filters. Clean or replace nozzles.
  7. Drain the purge, refill with your production adhesive and flush until no purge shows. Discard the first shots, reconnect nozzles and start production.

Which cleaner for which adhesive

Adhesive or jobCattie productNotes
Conventional hot melt (general purge)9007 hot melt purgeRun through the melter to push old adhesive and char out.
EVA, APO/metallocene, polyamide, SIS/SBS block rubber hot melt9008 hot melt purge cleanerOne purge cleaner listed for all of these adhesive types.
Hot melt, PSA and VAE glue residue8652 soy-based cleanerSoy-based cleaner for hot melt, PSA and VAE glue.
Reactive PUR (uncured), or switching from EVA/APO to PURPUR-Purge-8530PUR purge that also cleans APO and EVA when you switch a line to PUR.
Reactive PUR (uncured)9006 PUR cleanerPowder at room temperature, liquid at run temperature.
Reactive PUR, zero-VOC option8907 PUR cleaner100% solids, listed at 0 VOC.
Reactive PUR (already cured)Call usCured PUR does not remelt and is usually removed mechanically.

General guidance only. Check every product against your adhesive, your equipment maker’s manual and the SDS.

Before a holiday shutdown

Many plants shut down from mid-November through the holidays. That is the best time to clean. Purge before you shut down so old adhesive does not sit and char, and for PUR, purge and leave the purge in the unit. In January, flush with fresh adhesive before production. Call 800-249-0337 to plan your shutdown purge.

Gear and parts

  • Heat-resistant gloves, long sleeves and eye protection
  • Non-metal scrapers and spatulas
  • A metal container for purged material
  • Replacement filters and nozzles
  • Purge matched to your adhesive, and fresh production adhesive for the flush

Cattie cleaning products for this job

  • 9007 hot melt purge. General hot melt purge for tanks, hoses and guns.
  • 9008 hot melt purge cleaner. Purge cleaner for EVA, APO/metallocene, polyamide and SIS/SBS block rubber hot melts.
  • 8652 soy-based cleaner. Soy-based cleaner for hot melt, PSA and VAE glue.
  • PUR-Purge-8530. PUR purge. Also cleans APO and EVA out when you switch a line to PUR.
  • 9006 PUR cleaner. Powder at room temperature, liquid at run temperature.
  • 8907 PUR cleaner. 100% solids, listed at 0 VOC.

Related

How to purge PUR hot melt · Hot melt charring and gelling · Hot melt system trouble-shooting tips · Case sealer maintenance checklist · Hot melt adhesive

Hot melt cleaning FAQ

Do I need a purge or a cleaner?

A purge is run through the melter to push old adhesive and char out of the tank, hoses and nozzles. A cleaner dissolves residue on parts. Many plants use both at shutdown. Call 800-249-0337 and we help you pick.

How often should I clean a hot melt system?

Clean when you see char or gel, when you change adhesive types, and before a long shutdown. Many plants also do a full clean once or twice a year.

Can I use any purge with any adhesive?

No. Match the purge to the adhesive in the tank, and check it against your equipment maker’s manual. Polyamide and reactive PUR need special care.

What do I do after a holiday shutdown?

Heat up, flush with fresh adhesive until no purge or residue shows, discard the first shots, check nozzles and filters, then start production.

Where do I get data sheets?

Call 800-249-0337. We send the right data sheets for the product you use.

General plant guidance only, not a substitute for your process, SDS or line trials.

Need an adhesive or a cleaner?

Call 800-249-0337 or email sales@cattieadhesives.com. Cattie Adhesives, Quakertown, PA.