Home / Products / Hot melt PSA
Hot melt pressure-sensitive adhesive
Hot Melt Pressure Sensitive Adhesives (Hot Melt PSA)
This pressure sensitive hot melt stays tacky and bonds with pressure — no dryer, no solvent, no oven. Plants use it for packing slips, security bags, tapes, labels, laminations, interiors and assembly. Tell us the substrate and peel you need, and we match the grade.
Call 800-249-0337 Request a quote
Send us the film, liner and peel target, and we'll match a grade.
Why plants use hot melt PSA
Hot melt pressure-sensitive adhesive is applied molten, then stays tacky and wets out on contact. It bonds with pressure on a clean, dry surface. No water or solvent to dry, and no heat to activate the finished bond. Because it coats without a dryer, lines typically run fast and cure ovens are not needed. Tack and peel can be tuned to the job — permanent high peel or clean-removable — once the grade and coat weight are matched.
- No drying oven or solvent
- Typically fast coating speeds
- Typically bonds film and paper on contact
- Tack and peel tuned to the job
- Permanent or clean-removable, matched to the face stock, liner and peel target
Low surface energy plastics need an explicit match. See bonding LSE substrates and how to bond plastics.
Stock grades
These hot melt PSA product numbers are starting points, grouped by use. We match the grade to your substrate and equipment.
Labels, tapes, and general use
| Product number | Type | Typical use |
|---|---|---|
| 9938 | PSA hot melt, high tack, typically 4,200–5,500 cps at 350°F | General-purpose high-tack PSA for labels and tapes |
| 9337 | PSA hot melt, low viscosity, typically 1,900–2,700 cps at 350°F | When a lower viscosity is needed on the line |
| 9821 | PSA hot melt, high heat resistance, typically 30,000–40,000 cps at 350°F | When high heat resistance is needed |
| 9744 | PSA hot melt, typically 8,400–11,500 cps at 350°F | Stucco tape and labels |
Packaging and labeling
| Product number | Type | Typical use |
|---|---|---|
| 9810 | PSA hot melt, typically 1,600–2,300 cps at 350°F | Packing-slip envelopes and security-bag seals |
| 9713 | PSA hot melt, high tack, typically 2,100–3,000 cps at 350°F | Labels and tapes |
| 9452 | Rubber-based pressure-sensitive hot melt, typically 900–1,300 cps at 275°F | Bottle labeling; high tack and fast grab |
Foams, fabrics, and interiors
| Product number | Type | Typical use |
|---|---|---|
| 9748 | PSA hot melt, high tack, typically 9,000–14,000 cps at 350°F | Foams and fabrics. See foam fabricating. |
| 9195A | PSA hot melt, high tack, high heat resistance, typically 7,800–11,000 cps at 350°F | Automotive interior assembly, where specified |
Removable
| Product number | Type | Typical use |
|---|---|---|
| 8914 | Removable hot melt, higher viscosity, typically 15,000 cps at 350°F | Removable bonds that need more body. See fugitive hot melt. |
Bookbinding
| Product number | Type | Typical use |
|---|---|---|
| 9309 | PSA hot melt, typically 1,200–1,700 cps at 350°F | Bookbinding side seam. See bookbinding. |
Insect traps
| Product number | Type | Typical use |
|---|---|---|
| 9942 | Soft PSA hot melt, typically 300 cps at 300°F | Fly traps, insect traps, and window wrap. Other trap grades are on the insect and rodent trap adhesives page. |
Typical values, not specifications. Test for your application. Call 800-249-0337 for the TDS and SDS.
Laminations, graphic arts, direct mail, paper converting and other assembly jobs are matched to the face stock, liner, applicator and peel target. Call to match a grade.
Where hot melt PSA runs
Hot melt PSA runs on labels and tapes, packing-slip envelopes and security-bag seals, bottle labels, stucco tape and labels, foams and fabrics, automotive interiors where specified, removable bonds, bookbinding side seams, and insect traps. For other paper and film label jobs, masking and protective tapes, foam, film and foil laminations, graphic arts and direct mail, paper converting and product assembly, call to match a grade.
See packaging, bottle labeling, foam fabricating, bookbinding, insect and rodent traps, product assembly, automotive, industrial tapes and films, and adhesive coating services when you need PSA coated onto a substrate, as master rolls or slit rolls.
Running packing slips, labels, tape, foam, bookbinding or traps now? Tell us the film or part, the liner and the peel you need, and we'll quote a grade.
Call 800-249-0337 Request a quote
Send us the grade you run now and we'll match it.
We can formulate
When a stock grade is close but not right, we formulate peel, loop tack, shear, and viscosity for slot, roll or spray. We also tune clarity, low-temp tack and plasticizer resistance, and we match removable, permanent or repositionable behavior to the liner and face stock. LSE plastics need an explicit match. Color and viscosity can be set to the line.
How to run hot melt PSA
Coat weight sets tack and peel more than anything else. Start at your current weight and adjust. Keep tank temperature steady to avoid char, which can show up as specks on clear film. Tell us the film, the release liner and the surface the part goes onto, and we check the grade before a trial.
How to choose a hot melt pressure-sensitive adhesive
How to choose a pressure sensitive adhesive by end use · How to choose a label adhesive · How to solve pressure sensitive adhesive problems · How to solve insect and rodent trap adhesive problems · How to bond low surface energy substrates · How to bond plastics · How to bond all types of rubber
This page covers hot melt PSA only. Water-based, solvent-based and UV-cured pressure-sensitive adhesives are on the pressure sensitive adhesive page. Broader hot melt chemistries are on hot melt adhesive. For removable tipping and mailer grades, see fugitive hot melt.
FAQ
What is hot melt PSA?
Hot melt pressure-sensitive adhesive (hot melt PSA) is applied molten, then stays tacky and wets out on contact. It bonds with pressure on a clean, dry surface. No water, solvent, or heat is needed to activate the bond, and no dryer or cure oven is required.
Which hot melt PSA grades does Cattie offer?
Starting points, by use: 9938 for general high-tack labels and tapes; 9337 when you need a lower viscosity; 9821 when you need high heat resistance; 9744 for stucco tape and labels; 9810 for packing-slip envelopes and security-bag seals; 9713 for labels and tapes; 9452, a rubber-based pressure-sensitive hot melt with high tack and fast grab for bottle labeling; 9748 for foams and fabrics; 9195A for automotive interior assembly where specified; 8914 for removable bonds that need more body; 9309 for bookbinding side seam; and 9942, a soft PSA for fly traps, insect traps, and window wrap. Product numbers are starting points. We match the grade to your substrate and equipment.
Which grade is used for packing-slip envelopes?
9810 is our soft, aggressive grade for packing-slip envelopes and security-bag seals, typically 1,600–2,300 cps at 350°F. Tell us your film and coater.
Which grade is used for labels and tapes?
9713 is a high-tack pressure sensitive for labels and tapes. 9938 is the general-purpose high-tack starting point. Tell us the label stock and the line.
Which grade is used for bottle labeling?
9452 is a rubber-based pressure-sensitive hot melt with high tack and fast grab for bottle labeling. See bottle labeling, or call 800-249-0337 to match your labeler.
Which grade is used for foams and fabrics?
9748 is a high-tack PSA hot melt for foams and fabrics. See foam fabricating.
Which grade is used for a removable bond?
8914 is a higher-viscosity removable hot melt for bonds that need more body, typically 15,000 cps at 350°F. See fugitive hot melt.
Do you have an automotive interior grade?
9195A is a PSA hot melt for automotive interior where specified, typically 7,800–11,000 cps at 350°F. Call 800-249-0337 to talk through your part.
Can you run labels, tapes, laminations or assembly?
Yes. We supply hot melt PSA for paper and film labels, tapes, bottle labels, stucco tape and labels, foams and fabrics, removable bonds, bookbinding side seam, fly and insect traps, masking and protective tapes, foam, film and foil laminations, graphic arts and direct mail, paper converting and product assembly. Call to match a grade to your substrate and equipment.
How do I get a hot melt PSA match?
Call 800-249-0337 or email sales@cattieadhesives.com. Tell us the film or part, the release liner, the surface it goes onto, and the peel you need. Cattie Adhesives is based in Quakertown, PA.